Teltonika RUTX11 SIM Card Setup

The Teltonika RUTX11 is a dual-SIM 4G Cat 6 router with gigabit Ethernet and dual-band Wi-Fi. It takes a mini SIM, and a ThingSIM connects on whichever of O2, Vodafone, Three and EE is strongest once the APN is set in RutOS.

Specifications and menu paths checked against Teltonika's own documentation on 3 November 2026; sources are listed at the end. Menus can move between firmware versions, so if yours differs, follow the manual for your version.

What the RUTX11 Is

A gigabit router with two SIM slots and dual-band Wi-Fi. Teltonika has announced end of ordering on 3 February 2027 and end of support on 3 August 2032, with the RUTM11, RUTM16 and RUTC16 as replacements.

Which ThingSIM Suits the RUTX11

Compatible. It supports LTE Cat 6 with 3G fallback and no 2G. Teltonika lists LTE bands 1, 3, 5, 7, 8, 20, 28 and 32, plus 38, 40 and 41 for the versions sold in Europe, which cover the 4G bands used by all four UK networks. The RUTX11 has two mini SIM (2FF) slots, so order a physical ThingSIM and use the mini size. Some versions add an eSIM.

As a failover router that only carries traffic when the fixed line drops, UK 4-network 1 GB at £2.40 a month usually fits. For a site where it is the main connection for cameras or several devices, start on 5 GB at £8.85 and check usage after the first month.

Insert the SIM

1. Activate the SIM in the ThingSIM portal when you are ready to test; billing starts that day.
2. With the power disconnected, push the SIM holder button with the SIM needle and pull the holder out.
3. Place the mini SIM in the holder as the drawing in Teltonika's quick start guide shows, slide it back in, and fit the antennas.
4. Connect the power. On sites with heavy vibration, Teltonika suggests a thin layer of dielectric grease on the SIM contacts.

Set Up Mobile Data in RutOS

1. Log in to the WebUI at http://192.168.1.1 (user admin, password on the label) and go to Network → Mobile → General.
2. In Interface mob1s1a1 APN configuration (SIM 1), switch Auto APN off. In the APN field, enter the APN shown in your ThingSIM portal when you activate the SIM.
3. Set Authentication type to None and leave the username and password blank.
4. In SIM configuration, leave Deny data roaming off. A ThingSIM always connects to UK networks as a roaming SIM.
5. Leave the PIN field empty unless the SIM has a PIN, then click Save & Apply.

Two SIMs and Failover

Two-SIM models use one SIM at a time. Rules are set on the SIM Switch tab of Network → Mobile, with conditions such as weak signal, no network, network denied, data connection failure and data limit. Do not enable the On roaming condition for a ThingSIM: it would switch away from the SIM every time it connects, because a ThingSIM always roams. One UK 4-network ThingSIM already uses O2, Vodafone, Three and EE, so a second SIM mainly helps where a different provider or a private APN is wanted. Each active SIM is billed separately.

Check It Is Working

Status → Network → Mobile shows the SIM card state, operator, network type, connected band, signal quality (RSSI, RSRP, RSRQ, SINR) and the data connection state, with buttons to restart the connection or switch SIM slot. Teltonika RMS shows the same remotely, and the ThingSIM portal shows the SIM's usage.

Troubleshooting

• Operator shows but data does not connect: check Deny data roaming is off and Auto APN is off with the portal's APN entered on the interface for the slot the SIM is actually in.
• SIM not detected: power off, reseat the SIM in the holder the way the quick start drawing shows, and check it is the mini size.
• Signal but no data: check the SIM is activated in the ThingSIM portal, the APN matches the one shown in the portal exactly with no spaces, and data roaming is allowed. Then work through signal but no data in order.
• It worked, then stopped: look at the SIM's usage in the portal. A ThingSIM pauses when it reaches its monthly allowance; upgrade the plan straight away or wait for the reset.

Common Questions

Does a ThingSIM work in a Teltonika RUTX11?

Yes. The RUTX11's LTE bands cover all four UK networks. Put the SIM in, switch Auto APN off and enter the APN shown in your ThingSIM portal, and leave Deny data roaming off.

What size SIM does the RUTX11 take?

A mini SIM (2FF), the largest size on the ThingSIM trio card.

Does the RUTX11 work on 2G?

No. It is a 4G Cat 6 router with 3G fallback and no 2G, so it relies on 4G in the UK.

Related Guides

• Setting up a 4G router with a data SIM
• Port forwarding on a 4G router
• Teltonika routers and gateways
• APN settings: how to set up the APN on a device
• How much data does my device need?
• The best IoT and M2M SIM cards in the UK
• The UK 4-network 5 GB plan
• Compare every ThingSIM plan

Sources

Checked on 3 November 2026.

• Teltonika RUTX11 product page, specifications and versions: www.teltonika-networks.com/products/routers/rutx11
• Teltonika wiki: RUTX11 Mobile: wiki.teltonika-networks.com/view/RUTX11_Mobile
• Teltonika wiki: RUTX11 Network status: wiki.teltonika-networks.com/view/RUTX11_Network
• Teltonika wiki: RUT241 quick start guide (SIM holder steps): wiki.teltonika-networks.com/view/QSG_RUT241