Teltonika RUT241 SIM Card Setup

The Teltonika RUT241 is a compact 4G router with Wi-Fi, often used for CCTV, kiosks and failover. It takes a mini SIM, and a ThingSIM connects on whichever of O2, Vodafone, Three and EE is strongest once the APN is set in RutOS.

Specifications and menu paths checked against Teltonika's own documentation on 3 November 2026; sources are listed at the end. Menus can move between firmware versions, so if yours differs, follow the manual for your version.

What the RUT241 Is

An entry industrial router with Ethernet, Wi-Fi and digital input and output. It is a current model and replaced the RUT240.

Which ThingSIM Suits the RUT241

Compatible. It supports LTE Cat 4, with 3G and 2G fallback. Teltonika lists LTE bands 1, 3, 7, 8, 20 and 28 (or 1, 3, 5, 7, 8, 20 and 40, depending on the version) for the versions sold in Europe, which cover the 4G bands used by all four UK networks. The RUT241 has one mini SIM (2FF) slot, so order a physical ThingSIM and use the mini size. Versions with eSIM (2xxxxx codes) also have an eSIM that takes consumer eSIM profiles: add a ThingSIM eSIM under Network → Mobile → eSIM → Add new eSIM profile by pasting the activation code or uploading the QR code image. Teltonika says the download needs another working internet connection and the eSIM must then be set as the default SIM. These units also ship with a small bootstrap profile.

For a kiosk, vending machine, meter or card terminal, UK 4-network 1 GB at £2.40 a month is a safe start; telemetry alone often fits in 250 MB at £1.20. Check usage in the portal after the first month.

Insert the SIM

1. Activate the SIM in the ThingSIM portal when you are ready to test; billing starts that day.
2. With the power disconnected, push the SIM holder button with the SIM needle and pull the holder out.
3. Place the mini SIM in the holder as the drawing in Teltonika's quick start guide shows, slide it back in, and fit the antennas.
4. Connect the power. On sites with heavy vibration, Teltonika suggests a thin layer of dielectric grease on the SIM contacts.

Set Up Mobile Data in RutOS

1. Log in to the WebUI at http://192.168.1.1 (user admin, password on the label) and go to Network → Mobile → General.
2. In Interface mob1s1a1 APN configuration (SIM 1), switch Auto APN off. In the APN field, enter the APN shown in your ThingSIM portal when you activate the SIM.
3. Set Authentication type to None and leave the username and password blank.
4. In SIM configuration, leave Deny data roaming off. A ThingSIM always connects to UK networks as a roaming SIM.
5. Leave the PIN field empty unless the SIM has a PIN, then click Save & Apply.

Check It Is Working

Status → Network → Mobile shows the SIM card state, operator, network type, connected band, signal quality (RSSI, RSRP, RSRQ, SINR) and the data connection state, with buttons to restart the connection or switch SIM slot. Teltonika RMS shows the same remotely, and the ThingSIM portal shows the SIM's usage.

Troubleshooting

• Operator shows but data does not connect: check Deny data roaming is off and Auto APN is off with the portal's APN entered on the interface for the slot the SIM is actually in.
• SIM not detected: power off, reseat the SIM in the holder the way the quick start drawing shows, and check it is the mini size.
• Signal but no data: check the SIM is activated in the ThingSIM portal, the APN matches the one shown in the portal exactly with no spaces, and data roaming is allowed. Then work through signal but no data in order.
• It worked, then stopped: look at the SIM's usage in the portal. A ThingSIM pauses when it reaches its monthly allowance; upgrade the plan straight away or wait for the reset.

Common Questions

Does a ThingSIM work in a Teltonika RUT241?

Yes. The RUT241's LTE bands cover all four UK networks. Put the SIM in, switch Auto APN off and enter the APN shown in your ThingSIM portal, and leave Deny data roaming off.

What size SIM does the RUT241 take?

A mini SIM (2FF), the largest size on the ThingSIM trio card.

Can I use a ThingSIM eSIM in a RUT241?

Yes, on the eSIM versions. Add it under Network → Mobile → eSIM from the QR code or activation code while the router has another internet connection, then set the eSIM as the default SIM and enter the APN shown in your ThingSIM portal.

Does this router fall back to 2G?

Yes, it supports 2G as well as 3G and 4G, and ThingSIM SIMs work on 2G. UK 2G networks are due to close by 2033 at the latest.

Related Guides

• Setting up a 4G router with a data SIM
• Port forwarding on a 4G router
• Teltonika routers and gateways
• APN settings: how to set up the APN on a device
• How much data does my device need?
• The best IoT and M2M SIM cards in the UK
• The UK 4-network 1 GB plan
• Compare every ThingSIM plan

Sources

Checked on 3 November 2026.

• Teltonika RUT241 product page, specifications and versions: www.teltonika-networks.com/products/routers/rut241
• Teltonika wiki: RUT241 Mobile: wiki.teltonika-networks.com/view/RUT241_Mobile
• Teltonika wiki: RUT241 Network status: wiki.teltonika-networks.com/view/RUT241_Network
• Teltonika wiki: RUT241 eSIM: wiki.teltonika-networks.com/view/RUT241_eSIM
• Teltonika wiki: RUT241 quick start guide: wiki.teltonika-networks.com/view/QSG_RUT241