Teltonika RUT200 SIM Card Setup

Device setup Published

Set up a ThingSIM data SIM in a Teltonika RUT200: which SIM size and plan, inserting the SIM, the RutOS APN and roaming settings and troubleshooting.

The Teltonika RUT200 is an entry-level 4G router with Wi-Fi for kiosks, CCTV, signage and other IoT kit. It takes a mini SIM, and a ThingSIM connects on whichever of O2, Vodafone, Three and EE is strongest once the APN is set in RutOS.

Specifications and menu paths checked against Teltonika's own documentation on 3 November 2026; sources are listed at the end. Menus can move between firmware versions, so if yours differs, follow the manual for your version.

What the RUT200 Is

A compact router with two Ethernet ports and Wi-Fi. It is a current model and Teltonika's named replacement for the RUT240.

Which ThingSIM Suits the RUT200

Compatible. It supports LTE Cat 4, with 3G and 2G fallback. Teltonika lists LTE bands 1, 3, 5, 7, 8, 20 and 28, plus 38, 40 and 41 for the versions sold in Europe, which cover the 4G bands used by all four UK networks. The RUT200 has one mini SIM (2FF) slot, so order a physical ThingSIM and use the mini size. Some versions add an eSIM.

For a kiosk, vending machine, meter or card terminal, UK 4-network 1 GB at £2.40 a month is a safe start; telemetry alone often fits in 250 MB at £1.20. Check usage in the portal after the first month.

Insert the SIM

  1. Activate the SIM in the ThingSIM portal when you are ready to test; billing starts that day.
  2. With the power disconnected, push the SIM holder button with the SIM needle and pull the holder out.
  3. Place the mini SIM in the holder as the drawing in Teltonika's quick start guide shows, slide it back in, and fit the antennas.
  4. Connect the power. On sites with heavy vibration, Teltonika suggests a thin layer of dielectric grease on the SIM contacts.

Set Up Mobile Data in RutOS

  1. Log in to the WebUI at http://192.168.1.1 (user admin, password on the label) and go to Network → Mobile → General.
  2. In Interface mob1s1a1 APN configuration (SIM 1), switch Auto APN off. In the APN field, enter the APN shown in your ThingSIM portal when you activate the SIM.
  3. Set Authentication type to None and leave the username and password blank.
  4. In SIM configuration, leave Deny data roaming off. A ThingSIM always connects to UK networks as a roaming SIM.
  5. Leave the PIN field empty unless the SIM has a PIN, then click Save & Apply.

Check It Is Working

Status → Network → Mobile shows the SIM card state, operator, network type, connected band, signal quality (RSSI, RSRP, RSRQ, SINR) and the data connection state, with buttons to restart the connection or switch SIM slot. Teltonika RMS shows the same remotely, and the ThingSIM portal shows the SIM's usage.

Troubleshooting

  • Operator shows but data does not connect: check Deny data roaming is off and Auto APN is off with the portal's APN entered on the interface for the slot the SIM is actually in.
  • SIM not detected: power off, reseat the SIM in the holder the way the quick start drawing shows, and check it is the mini size.
  • Signal but no data: check the SIM is activated in the ThingSIM portal, the APN matches the one shown in the portal exactly with no spaces, and data roaming is allowed. Then work through signal but no data in order.
  • It worked, then stopped: look at the SIM's usage in the portal. A ThingSIM pauses when it reaches its monthly allowance; upgrade the plan straight away or wait for the reset.

Common Questions

Does a ThingSIM work in a Teltonika RUT200?

Yes. The RUT200's LTE bands cover all four UK networks. Put the SIM in, switch Auto APN off and enter the APN shown in your ThingSIM portal, and leave Deny data roaming off.

What size SIM does the RUT200 take?

A mini SIM (2FF), the largest size on the ThingSIM trio card.

Does this router fall back to 2G?

Yes, it supports 2G as well as 3G and 4G, and ThingSIM SIMs work on 2G. UK 2G networks are due to close by 2033 at the latest.

Sources

Checked on 3 November 2026.